Same drill 11-3-2012

Drilling continued in the steel for the north inner sill.  Lenny is doing the honors with the piece in situ, using the drill in the horizontal position, while Bob is providing the lubricant.  The splice piece had already been drilled, but not the long pieces.

Both inner sills have now been fitted with the reinforcing steel.  They will eventually be bolted together with pipe spacers between for added stabilization.  The tie rods passing through the sills will be tensioned later as well.

Meanwhile, Craig is fitting the corner post for the west door that he has fabricated.  The steps into the car were also reinstalled at this end so we don't have to walk to the other end, often ducking extended tie rods, to access the car.

South sill steel fitted 10-20-2012

We started by marking the holes to be drilled for the splice in the two long pieces of steel on the south inner sill.  They were then removed from the sill and lined up for drilling and bolting the splice in place.  Not shown, but taking significant time was the process of moving the tie rods that were passing through the lower sills and the steel, from side to side in order to remove the steel beams.

The magnetic drill was again  used to drill the holes for bolting the splice piece to the larger pieces.  John M. is doing the honors while John E. and Tom are advising.  Craig in the background can't stay away from the wood.

One side is together and the other is ready to bolted.  It has been decided to bolt and weld the steel together after consulting engineers on the best way to do it.  On a prior post I had suggested that bolts alone were going to be used, but they will be welded as well.

The steel that now runs the length of the car weighs over twice as much as the two pieces before joining, so it took a come-along and some coaxing to get it back in place.  Craig is drilling holes to accommodate the heads of the bolts in the sill after the steel is in place.  Finally it all fits together.

With the steel removed, the sills are sagging as well as shifted side to side as in the photo on the left.  After clamping the steel in place on the south inner sill, the alignment is much improved as in the photo on the right.  Note the splice in the sill (done in the past) near the end of the steel on the left is aligned much better on the right.

Bridging the gap 9-15-12

A piece of angle steel as shown above will be used to fasten the two longer pieces in the center of the car.  It was modified slightly to fit snugly against the larger pieces by grinding the inside angle to a sharp angle rather than rounded as most are when they are manufactured.  It was initially planned to weld the pieces together, although subsequent information obtained suggested that bolting would be better considering the repeated stresses that would occur as part of a train.  It was felt that welds would be vulnerable to breaking more easily.

So, back to our friend the mag drill.  Drilling was a little tricky because the width of the steel was such that the magnet couldn't hold optimally, but it worked.

Like so.

Meanwhile, Tom was making a prototype bracket to refasten the cross-pieces between the inner and intermediate sills that had been removed, cutting the mortises.  These should be quite stable after tensioning the tie rods across the car.

Steel bracing

We have received a request to show some of the steel bracing in 470, and this posting will attempt to do that.  There is a steel piece that runs the length of the car as shown above.  Vertical posts are present at the bends of the long piece.  Each end is anchored through the sill  at the end of the car as shown below.

Each end of the brace is rounded and threaded, and passes through the sill, and is fastened with a nut.  The sill on the left end as we face this side of the car has been exposed to water from the icebox which was just above, and a portion is to be replaced.  this nut was also rusted on. 

Steel IV 9-1-12

After spending many hours and bruised knuckles moving tie rods back and forth, it was determined that they moved easier when the holes in the sills were enlarged slightly.  This was done to the inner and intermediate sills only, leaving the outer sills intact.  Craig is working on one of the intermediate sills in the photo above.

Meanwhile, John is fabricating more clamps to hold the steel tightly to the inner sills.

Thusly.  Looks like they will fit.  Now, how do we fasten the two long pieces on each inner sill together in the middle?  More to come.

Levitating steel - 8-18-12

Holes have been drilled in the steel, and it is time for a trial run to fit them together.

The beams could be lifted by 3 or 4 people, but hydraulic jacks were used to press them into place,  We also had rachet straps in place to not only help in raising, but also for safety to prevent an "unforseen" descent.  Lenny is minding the jack in this photo.

One side is close.

But  there is a speed bump.  Most of the holes were aligned well, but a few had to be enlarged slightly.

Tom made clamps out of angle iron and thread stock to tighten up and hold the steel in place.  (I didn't know he was left handed!)  The tie rods have been threaded through the beam on the right and are being worked through the holes in the beam on the left.

It's looking good.  It just needs a little adjusting here and there.

Here is a closer look.  Don't forget you can enlarge photos by clicking on them.

More steel - 8-4-12

Work continues fitting and drilling the steel.  The holes for the tie rods fit fairly well with minimal redoing.

Rich and Tom are working on the splice in the sill that had been done prior to our acquiring 470.  We replaced the bolts above Tom's toes recently, and there will have to be accommodation made for them in the steel on this side.

The bolts were removed and the steel put in position so that the drill sites could be marked through the sill.

Tie rod holes have been drilled in the piece on the left.  Note the flex in the sill on the left that has been blocked up.  The steel should correct the misalignments.