End Plates - 6-26-2013

In a previous post we showed the making of

a pattern of the wood end panel over the door of 

the car.  One of the originals was fairly well 

preserved.  

The first photo shows the pattern 

as well as the two steel plates that were 

made from the pattern.  These will be fastened 

over the doors and become part of the steel 

reinforcement at each end of the car.




The second photo shows Bob and Lenny
clamping the plate in place.  It was installed
with minimal forcing although I did wear
my earplugs.










Another view of the plate in place.  Tom is
applying a clamp in the center.











A little re-shaping had to be done to fit the
wood trim.  The two ends were very similar
but not identical.

Wood work - 4-20 & 5-4-2013

Prior to the work session on 4-20, Craig 

fabricated replacement sill extensions for 

the end platforms using the ones we had

removed as patterns. The first photo shows 

his shop where he has glued the pieces for 

lamination together.

The second photo shows the finished extensions at the work site ready for installation.

Work continued on fitting the brackets for the cross braces.  Dale is doing some trimming on one of the braces.

Craig continues to fill and sand the corner posts as shown in the next photo.  Some are being reused, while others needed replacement.

One of the fascia pieces is being installed in this photo.  Some of the new window framing is also visible.

Thanks to Craig and Glenn for taking these photos in my absence.

Replacing I-beam, 3-30-2013

 It was discovered that the floor was uneven at the east end of the car due to the I-beam supporting that area not being straight.  The beam was replaced by jacking up the car as shown in the the first picture.  The beam to be removed is behind the jack.

A chain was secured to the beam, and a cable puller (anchored to Lenny's truck) was fastened to the chain.  The beam was then slid out from under the car on to saw horses as shown in the next photo.

Fortunately we had a good crew this day.  I believe it can be seen that the right end of the beam is sagging a bit from a prior repair.

The last photo shows the new straight beam in place.  It is a bit short to support the outer sills, so a piece of angle steel was inserted on it as shown.  The sills appear much straighter now.

Installing cross-brace brackets - 3/28-4/6/2013

With the angle steel pieces in place along the inner sills, the cross braces abutting the steel must be stabilized.  Brackets have been fabricated (see Feb 2nd posting) to accomplish this.

In the first photo a bracket has been set in place on the cross brace on the left.

The second photo shows a view from below.  You may recall that originally the braces were mortised into the sill, but the tenons had to be cut to place the steel.











The third photo shows the cutout for the truss rod that is adjacent to the brace.  The finish had to be removed from the angle piece prior to welding.

                                 

The welding was done from below as shown in these two photos.   Precautions were observed with water hoses and fire extinguishers immediately available.  No untoward events occurred.

The end result is shown in these two photos.  Following welding, bolts were placed through the brackets fixing the end of the brace securely in place.

Thanks to Tom and Glenn for taking photos in my absence.

Ditto - March 2,2013

We continued fitting the bolts through the steel  angles and the inner sills, and were able to get things lined up without further drilling (or re-drilling) of the holes in the sills.  Nuts were placed on most of the bolts.  There are two bolts that were short that went through the splices, that will have to be ordered.  Everything seems to be nice and straight, and like Bob said, it is like walking on a sidewalk now.  Next will be fitting the blocks and brackets between the inner and intermediate sills.  These likely will have to be individually cut and fitted.

Meanwhile John continued work on the pattern for the steel pieces that go over the doorways on each end.  There will be essentially a "cage" of steel at each end of the car to provide rigidity as well as the steel running the length of the car.

Two men from the company that we have been negotiating with to fabricate the steel visited the site to better understand out plans, and are interested in participating in the project.

Getting it together - Feb. 16, 2013

Initially, we replaced the pivot blocks on both ends of the car that Craig had made previously.  We then pulled the angle steel pieces together against the inner sills in preparation for beginning to install the long bolts through the steel, sills and pipes.  That involved alignment of several holes drilled in wood and steel, and I might just say that we have a little more drilling to do.

                  

Some of the bolts were passed through without difficulty (in the far lower right and upper center of this picture), but others need re-aligning of the holes.  Once these are in place the angle steel pieces can be drawn tight against each other with the pipes acting as spacers through the sills.

Meanwhile John and Glenn were making a pattern of the piece of wood that was over the doors at each end of the car in preparation for fabricating pieces of steel that will be inserted over the doors as part of the reinforcing at the car ends.  Note that the curve at the top is a complex one, with a cutout in the center for the top of the door.  This is being done on a piece of Masonite.

During the last two weeks Lenny has located a company that can do steel fabrication, and has offered to do the brackets for the inter-sill blocks (see previous post for photos) at a reasonable price.  They seem interested in our project and hopefully can be helpful as we continue to reinforce the car to be up to current standards for rail use.

We were pleased to have Craig join us for lunch today, and thank Maggie for bringing him to the work site.

Metal shop Feb. 2. 2013

We started the day replacing the tie rods through the north piece of angle steel, on the left, and bringing them out through the outer sill.  We then positioned the wooden blocks between the inner sills so that the mortises fit into the tenons and began to clamp the inner sills together.  Dale and John M. are working to get everything to fit.

Most of the original blocks could be reused, but some new ones had to be fabricated as well.  The two angle steels are in position ready to be moved toward the center against the wooden inner sills and bolted together with long bolts passing through the black pipes.  One of the pipes is seen just above the clamp in the photo.  The pipes butt against the steel to maintain proper distance between them.

A "speedbump" was encountered, however,  We could not begin to bolt the steel together because the body-bolster truss-blocks have not yet been replaced, and as can be seen here they are not in good condition.  The blocks are in the process of being fabricated.

So, on to other things.  The plywood used for temporary flooring was removed, and the blocks between the outer and intermediate sills were repositioned as needed.  Washers and lock nuts were placed on all the horizontal tie rods but not tensioned as yet.

Meanwhile, Lenny was fabricating brackets for the blocks between the intermediate and inner sills.  The tenons had been cut at the inner ends to remove the blocks to accommodate the angle steel.  The brackets will be welded to the angle and will support the blocks against it.

The brackets were made from angle steel, and cut and bent as shown in this photo.  Tom S. did the design and started fabricating them before he met up with a knife.  The tenons were preserved on the outer end as can be seen on the block below.








Bob (right) and Dale started working on cutting grooves in the framing to accommodate more steel framing that will be placed into the ends of the car.  More on this later.